Products

Rudder retaining clips in plastic or stainless steel.

Suitable for up to 6mm rope. A range of high quality 25mm single blocks from Seasure, all of which have been tested in the most extreme race conditions and proven over time, and you will often find them in use after more than 30 years! The high strength to weight ratio and simple construction give years of trouble free service.

The '00' range offers an unparalleled range of control line configuration opportunities. They feature hollow rivets for lightness and tough plastic sheaves that provide a good bearing surface allowing easy rotation under a range of load conditions. The robust electro-polished 316 stainless steel construction also gives a high chafe resistance should any feed or take-off misalignment occur. Made in the UK from 316 stainless steel and tough "Arnite" plastic.

Suitable for up to 6mm rope. A range of high quality 25mm double blocks from Seasure, all of which have been tested in the most extreme race conditions and proven over time, and you will often find them in use after more than 30 years! The high strength to weight ratio and simple construction give years of trouble free service.

The '00' range offers an unparalleled range of control line configuration opportunities. Their classic design has stood the test of time. They feature hollow rivets for lightness and tough plastic sheaves that provide a good bearing surface allowing easy rotation under a range of load conditions. The robust electro-polished 316 stainless steel construction also gives a high chafe resistance should any feed or take-off misalignment occur. Made in the UK from 316 stainless steel and tough "Arnite" plastic.

Suitable for up to 6mm rope. A range of high quality 25mm treble blocks from Seasure, all of which have been tested in the most extreme race conditions and proven over time, and you will often find them in use after more than 30 years! The high strength to weight ratio and simple construction give years of trouble free service.

The '00' range offers an unparalleled range of control line configuration opportunities. Their classic design has stood the test of time. They feature hollow rivets for lightness and tough plastic sheaves that provide a good bearing surface allowing easy rotation under a range of load conditions. The robust electro-polished 316 stainless steel construction also gives a high chafe resistance should any feed or take-off misalignment occur. Made in the UK from 316 stainless steel and tough "Arnite" plastic.

Suitable for up to 6mm rope. A range of high quality 25mm bolt down blocks from Seasure, all of which have been tested in the most extreme race conditions and proven over time, and you will often find them in use after more than 30 years! The high strength to weight ratio and simple construction give years of trouble free service.

The '00' range offers an unparalleled range of control line configuration opportunities. Their classic design has stood the test of time. They feature hollow rivets for lightness and tough plastic sheaves that provide a good bearing surface allowing easy rotation under a range of load conditions. The robust electro-polished 316 stainless steel construction also gives a high chafe resistance should any feed or take-off misalignment occur. Made in the UK from 316 stainless steel and tough "Arnite" plastic.

Fabricated from 316 stainless steel this well tested and reliable design is tough and strong. As well as being used for inner forestays they can also used as a safety device on boats fitted with furling headsails allowing a storm jib to be flown in an emergency. Essential for fast assembly of inner forestays in bad weather conditions.

There are 2 sizes in the range, for 6mm-8mm wire size. Manufactured in the UK by SeaSure.

Carbon Fibre roller race blocks, the use of Carbon Fibre needle roller bearings means that they run well even under high loads. Made from Acetal and Stainless Steel with Carbon Fibre Bearings. Suitable for up to 8mm rope.

Carbon Fibre roller race blocks, the use of Carbon Fibre needle roller bearings means that they run well even under high loads. Made from Acetal and Stainless Steel with Carbon Fibre Bearings. Suitable for up to 8mm rope.

The high strength to weight ratio and simple construction gives years of trouble free service. Made from Stainless Steel and "Arnite" plastic. Suitable for up to 10mm rope.

Carbon Fibre roller race blocks, the use of Carbon Fibre needle roller bearings means that they run well even under high loads. Made from Acetal and Stainless Steel with Carbon Fibre Bearings. Suitable for up to 10mm rope.